What are parallel shafts?

Parallel-tip shafts are the same, within the model type, for each iron but are trimmed to fit the length for each club. As a result, parallel-tip shafts are heavier in the longer irons and weigh less in the shorter irons.

How do you tell if a shaft is parallel or tapered?

The difference between a parallel tip shaft and a taper tip shaft is the tip diameter and shaft weight. All golf shafts taper from the butt to the tip, but parallel tips stop tapering below the last step, while the taper tips, continues to narrow.

Are all .370 shafts parallel?

370 hosel is a parallel tip hosel. The only difference between the two is tip diameter and weight. Taper tipped shafts are a constant weight throughout the irons and the parallel tipped shafts are a decending weight.

What are the different types of golf shafts?

There are generally five types of shaft flex: ladies, senior, regular, stiff and extra stiff. If you have a flex that doesn't match your swing speed then you're probably losing distance and/or accuracy. An incorrect shaft flex becomes more noticeable the longer the club gets (ie. with the driver).

How far should you hit a 7 iron?

A standard amateur golfer can hit a 7 iron from 128 yards to 158 yards. The lower range will be for women and senior golfers. To hit the ball over 150 yards in total distance with a 7 iron club, an amateur golfer will have to have a good swing and be physically fit.

Are Vokey wedges taper tip?

355" taper tip shaft.

What does PTIP mean in golf shafts?

“Tipping” or “tip trimming,” as it's sometimes called, means trimming a club shaft from the clubhead end, not from the grip end where it's most often cut.

How much does tipping a shaft effect Flex?

Tipping any TPT Red Range shaft 1 inch will result in a stiffness increase of 5 cycles per minute (cpm), or one-half flex. This removes the need for half flexes in the Red Range. When a 14 Lo is tipped 1 inch, for example, it effectively becomes a 13.5 Lo.

What happens when you shorten a golf club?

The more shaft you cut off, the lighter, more stiff, and effectively flatter the club becomes. For every 1/2 inch you remove, you will lose approximately three swingweight points. You can readjust the swingweight by adding lead tape to the head of the club. Any amount of cutting will slightly stiffen the club.

Which end of a golf shaft do you cut?

The butt end of the shaft is grip end. If you are shortening or extending the length of a golf club, this is where you will cut. If you want to change the play-ability of the club (feel, flex to a certain extent, spin rate, dispersion), you will be cutting the tip end of the shaft.

What tip size are Pxg irons?

355" ferrule includes a required tip spacer that needs to be applied to the . 355" shaft tip after abrasion and prior to installation.

Are all golf club shafts the same diameter?

The shaft tip size is the the diameter of the tip portion of the shaft. For irons, this will usually be 0.370" (parallel) or 0.355" (tapered). For woods, it will be either 0.335" or 0.350". To choose the tip size needed, you'll want to match it with the ID (inside diameter) of the hosel of the golf club head.

Can you tip trim taper tip shafts?

Instead of stocking individual shafts for every club, the same shaft can be tip trimmed to fit any iron club. In additional to trimming the tip, you'll then need to trim the butt end, to achieve the final desired club length.

Why does Taylormade tip their shafts?

Hard stepping and additional tipping of a shaft will make the club feel and play firmer than its standard profile (decreases flex). Soft stepping and reduced tipping of a shaft will make the club feel and play softer (increases flex).

What does hard stepping a shaft mean?

Stepping shafts is a method of reshafting that focuses on a flex between the specific designations, say, between a regular and a stiff flex. "Hard stepping" would make a shaft stiffer, "soft stepping," more flexible.

Does shortening a golf shaft make it stiffer?

"Cutting more of the tip will have the effect of getting rid of some of the weaker end of the shaft which, in turn, makes the shaft play and feel more stiff.

What shaft is in Vokey wedges?

The stock shaft for the new Slate Blue SM8 is the True Temper Wedge Flex shaft and is fitted with an eye-catching Blue/White/Black Golf Pride grip with the BV (Bob Vokey) wings on display down the front. A new premium finish for the number 1 wedge on Tour.

What shaft tip is in Vokey wedges?

Do the Vokey SM4 wedges have a . 355 or . 370 tip.

Why do I hit my 3 wood as far as my driver?

Players who hit their 3- or 5-wood as far or longer than their driver are typically using too little loft with the driver for their clubhead speed. You know, it's a funny thing with the driver and its loft compared to the other clubs in the bag.

Should you always take a divot with irons?

In general, you should take a divot with practically every iron shot. This is because the ball is played from the ground. Taking a divot improves your margin for error, making a good strike much more likely.

Is a 250 yard drive good?

The average driving distance for a golfer with a 5 handicap or less is 250 yards. You might think that's kind of low for a good golfer but it's pretty realistic for someone who isn't a professional. If you hit the ball the average distance you're really not that far away from the average distance of a scratch golfer.